HHO CELL CAR KITS

HHO Cars Break The Access Rules To Energy Your First HHO Cell Is Your First Step To Free Energy…. And Jeez ! It's So Good !

Jun
13

How To Connect In Parallel ?

Posted under HHO Cell Technicals by admin

This article talks about how to & why connect in parallel 2 or more HHO Cells that use plates as electrodes. Most known type is Dry Cell, but any kind of unit using more than 2 plates as electrodes can be connected in parallel.

If you need to connect 2 or more Mason Jar type units, please refer to this article : http://www.hhocellcarkits.com/hho-cell-how-to/how-to-connect-in-series

Well, you generally will have to connect plates  HHO cells in parallel because :

1 : the configuration of the plates is dividing voltage by the number of gaps the current have to “pass” through between a + connected plate and a – connected plate.

2 : Inside a HHO Cell, electrolysis will become significant at a little more than 2 volts, let say 2.5 volt.

There is a lot of litterature about electrolysis, you will read here or there that 1.8V or 1.6V or even less ( theorically 1.24 v )  is required for electrolysis to occur. Well, that may be true in very specific conditions, but practically, the cars HHO cell designs need more than 2 volts to give significant results. I’ve been testing a lot of HHO units & I’ve seen that 2,3,4,5 intervals are ok, but 6 is too much for a 12 volts system.

So if your cells are counting more than 2 intervals each,( that’s 3), when connecting them in series you will get 6 intervals that will divide by 6 your 12 volts battery power. In fact you get 13.5 volts when driving. So 13.5:6 = 2.25 volt. This is a very optimistic schem untill HHO cells very often count 4 or 5 intervals between + & – plates….

That’s why the parallel connection is required for dry cells or other plates designs. You simply have to wire + on + & – on – ! It’s a kid game….

However, when choosing or building a hho cell, the closer you are to 2 volts per gap, the less heat you will product. Regarding this, the +nnnn- config. seems great. You can try the +nnnnn- config. if supplied voltage is 13volt or a little more. Before deciding this test the voltage on your car when engine is running at 2-3000 rpm.

Also remember that when adding a second cell, connected in parallel, to your system, you theorically will double the amps drawing. Think of it before running the system and may be change your electrolytic bath to reach a twice lower electrolyte concentration. Other way you may burn fuses, damage your installation, or simply draw too much amps and reduce your mileage gain.

All right ? Just go ahead & be carefull on the road !

Christian, Your Brother In HHO.

Technorati Tags: , , , ,

Oct
31

How to connect in series ?

Posted under HHO Cell How To, HHO Cell Technicals by admin

This article talks about how to connect Mason Jar type HHO Cells

If you want to connect 2 or more Dry Cells, or any HHO cell using plates as electrodes, this article is not for you, refer to this article : How to connect HHO Cells parallel or refer to the manual that came with your Dry Cell.

For your information, Dry Cells are to be connected in parallel rather than serie : + on + & – on – …. Easy as your ABC !

Ok, that being said, let’s talk about how to connect Mason Jar type cells :

First a few tips to remember:


* Remember that the amperage in “hot” conditions from your HHO Cell is higher than the one in cold :

If you measure the amperage cold, one must imagine that when your HHO generator will have been running half an hour or more, it will be hotter and amperage will have increased considerably, often around 50%!. That is to say : if you have 4 amps cold, you’ll have about 6 hot …. Quite important if you don’t want water to boil….

* Do not exceed 4 amps/cell current consumption for Mason Jar type  HHO Cell. Tresspassing this is a potential overheating risk  that could damage the cell and possibly your engine. If you own a different HHO Cell (ie dry cell ) carefully follow the manufacturer’s instructions about it.

* Always prefer low amps soluce. One should always prefer an installation with two cells’ pulling 4 amps total (2/Cell ) rather than 1 single cell drawing 4 amps, your installation will run with a lower temp, and your electrodes life will be significantly longer

* When you add the electrolyte:

1 Always add small quantity, preferably ½ teaspoon.
2 Check amps with an ammeter to make sure not to exceed 4 amps per cell
3 Always use the manufacturer’s recommended electrolyte for your cell
4 Newbies are very often using baking soda as an electrolyte, great way to learn ! But compensation is to drain and replace your water / electrolyte every 1000 to 3000 km. The more amps, the more often you’ll have to change (1000 km) your mix.  See here other electrolytes you can use

* Remember always that using HHO gas, you became a pioneer in fuel burn, bravo!  The planet and your wallet are thanking you!
But BEWARE, that also means you are left to yourself, industrialization policy has not yet been through this, you are in an area with no rules and no established laws. Therefore caution be preferred in any circumstance

* Remind yourself that the HHO gas is highly flammable and electrolysis that involves chemical reactions. So unless you’re a chemist High flying: Do not play the little budding chemist!

If you want to learn more about how to determine the HHO production needed for your vehicle, you can read this article http://www.hhocellcarkits.com/hho-cell-technicals/how-much-hho-output-for-maximised-savings

Well, that being said, let’s head on over the assembly of several HHO Cells in series :

Series HHO Cell Car Kits Connection

Series HHO Cell Car Kits Connection

In the diagram we have chosen to connect the cells by pairs, the example shows 3X2 cells but the arrangement is the same for 2 or 2×2 cells.

Primary effect when choosing a series connection by pairs is to decrease the voltage to 6 volts in each cell. This is not a problem since electrolysis requires only 2 volts.
You can mount as many cells as you want while respecting the limits described in this article: http://www.hhocellcarkits.com/hho-cell-technicals/how-much-hho-output-for-maximised-savings

According to users testimony, connecting in series reduces the voltage and, again according to users testimony, thereby reduce the heating of water & eventual steaming. It’s a safer way to run your HHO Car

However be aware that : a series circuit will reduce the overall amperage consistently, you’ll be forced to double or triple the dose of bicarbonate or other electrolyte you use. Try to remember if you switch back to a single cell or a parallel connection…. Otherwise it could seriously boil in there!

You should also know: the series circuit by 3 or more HHO Cells is not recommended and you’ll notice right away yourself that this is not a good idea, Because the amperage decreases so much that it goes on almost nothing! So always 2 or 2X2 or 3X2, as in the picture.

If you have 3 cells to connect, you will of course find difficult to mount them in pairs … .. And a 3 Series, as stated above, it is not profitable. You can then opt for a parallel connection, it poses no problem when being reasonable on each cell amperage (3 to 3.5 amps when cold ) . Nothing more simple than a parallel connection: + on + & – on – ….. I’ll make you a drawing when I have time, or a small video!

– The advantage of parallel connection is that you do not increase the electrolyte dose, if you have 3 cells that draw 3 amps each, mounted in parallel will consume …? Won! 9 Amps in full. We have seen that the calculation is not as simple with a serial connection.

– The disadvantage is that you keep a voltage of 12 volts in each cell, which predisposes you to more easily overheat when overdosing electrolyte.

So to summarize : it is better to avoid odd numbers of Mason Jar HHO cells.  And if you need more than 2 or 3 cells of this type, you may consider to opt for a Dry Cell, which takes less space and cost not much more  than 3 or 4 jars.

Let’s continue on:


Start by finding a place and fix your additional cells next to your first cell. Then two things are to be changed : the electrical connection and vacuum system.
Nessecary stuff is usually supplied with the first cell and the additional cell.

ELECTRICITY:

On the “old” cell, disconnect the cable from the black terminal (ground) and reconnect it to the black terminal of the new cell.
Then connect the small red ( or whatever ) cable link supplied with the additional cell: one end to the black terminal of your first cell, and the other end on the red terminal of the new cell.

You just plug in your cells “in series”. 6 volts are now distributed to each cell.

VACUUM SYSTEM:

Use the  T fittings supplied with your first cell and/or with additional cells for connecting all your cells.
If you install more than 2 additional cells it will be necessary to use a manifold …………………. to connect all cells together and then directs the HHO gas to the engine’s air intake.
Always keep check valve between the cells and engine. A single valve on the main hose is sufficient.

Where to find spare parts?


Listed below sites offer an interesting selection of parts, which can enable you to supplement or customize your installation.

Greentechexpress
WalkingEagleSolution
HHOxygen
HHO KitsDirect

Happy install everybody !

Christian, Your Brother In HHO.

Technorati Tags: , , , , , , , , , ,

Oct
13

How Much HHO Output For Maximised Savings ?

Posted under HHO Cell Technicals by admin

One of the most frequently asked question by a HHO Cell user !
How much HHO gas do I need to produce to save as much as possible gas?

Another one : Is there an ideal HHO Gas quantity ??

Another great one : Do I need to produce as much gas as possible?

There are still no clear answers to these questions, the HHO does not earn enough money, so …. no industrial and no official agency is interested in this case study, so no scientific data, we are left to ourselves, and after all, the better, because the day a politician will stick his nose in there, it will be as usual : We’ll be f….d ! ( forwarded ? Freaked ? … ? )

But we can still tell you what to do to optimize your HHO gas production and achieve maximum savings, ie, a “nickel chromium” setting can save you up to 50% fuel !

So let’s go :

Well, before we go, here is an indication :

All HHO cell users with little experience, whether in the United States or Europe agree that the ideal gas production per minute is between 1/4 and 1/2 of the cylinders volume of your future HHO car. For example if your engine is 2 liter, it takes 0.5 to 1 liter per minute HHO gas output to get significant savings

My advice :

I sincerely believe that the truth is quite close to 1/2
Ok, so let’s go this time !
Many believe that the more you produce gas the more you realize fuel economy, they often think that electricity needed for electrolysis of water is somehow “free” since in any case, the motor turns… Both assertions are false!

Here’s why:

When the engine is running, and there is a need for electricity, it transmits its energy through a belt to the alternator, which then produces the electricity. This electricity is in fact a measurable rotation brake  of the engine, so it causes excessive fuel consumption to fight against the resistance of the alternator. If for example you’re going downhil, you should re-accelerate earlier at the bottom of the descent to maintain your speed. The electrical energy produced by the alternator cost you fuel.

Now look at the HHO gas side. When we burn it, it returns less energy than the energy expended to create it … More, there are several energy conversions involved, as there is no 100% possible efficiency, energy is lost during each conversion.

The conversions are: mechanical to electrical (generator), electrical to chemical (electrolysis), chemical to mechanical (burning the HHO). Finally, once HHO gas burned, you will not be returned more than 20-25% of the energy used to create it…..
But do not despair immediately, the fuel savings are still achievable with this energy!

HHO benefit is not realized because it substitute to your regular fuel, but because it optimizes the combustion of fuel.
Our exhaust  are filled with unused particles, there is an enormous amount of energy unused, and the HHO gas simply allows us to “recover” a part of this raging waste. And a small part of a huge amount, is very interesting. My banker told me that long ago ! This makes the HHO precious.

Nevertheless there is a limit, an optimum amount of gas which, if you trespass, begin to increase your consomption again. At this moment the energy consumed to produce the HHO is greater than what is restituted when optimizing your air/fuel mix combustion.

Currently the only way to know the volume of gas you need is the method “test – errors” :

At each refueling, gradually increase your gas production.

# 1 With bicarbonate, or whatever electrolyte you use, addition in your HHO Cell tank, giving yourself a 50-60 °C temp limit ( 60 is pretty high ) of the water in your generator after a continuous 15-30 minutes work. When the weather is hot this limit will prevent you from reaching too high a temperature that can damage the generator and/or cause the water suction in your engine.

# 2 Or, if you’ve already reached the temp limit, adding a cell to produce additional gas … .. You just change the configuration of your system, meaning that ie, in the Mason Jar HHO Cell configuration you now have 2 cells connected in serie, using 6 volts each, instead of 1 cell with 12 volts. You should know that electrolysis does need no more  than 2 volts, so in a single cell device, 10 volts are “lost” and only  produce heat & steam. For plates electrodes it’s a bit different, you must refer to your owner manual when connecting 2 cells.
Then If you want to restart at the same gas production level, repeat the above described, knowing still that: a series connection will reduce the overall amperage consistently, you’ll be forced to double or triple the quantity of bicarbonate or other electrolyte you use . Try to remember what you’ve done if you switch back to a single cell or a parallel connection. … Otherwise it could seriously boil  in there!

You should also know that the 3 or more series circuit is not recommended and you’ll notice right away yourself that this is not a good idea, because the amperage decreases so that it finally turns to almost nothing! In a Mason Jar system you even can ad as much as electrolyte you want in a 3 serie circuit, you’ll never bypass a total 5-7 amps for your install ! This is due to wide space between electrodes + reduced ( compared to plates ) electrode surface

Personally I opted for a parallel connection for my 3 set Mason Jar system,  keeping reasonable amperage of each cell (3 to 3.5 amp when cold ) it poses no problem.

That being said, an ammeter is the best way to measure and store the right amount of baking soda, in all  FIGS  cases.

Well, whatever HHO cell you use, at some point you’ll reach your fuel economy peak (without knowing it ) and when you add electrolyte again, your fuel savings will begin to diminish, you know now that the previous dosage was the best one ! Just need to drain your HHO generator and fill again with water/electrolyte ideal mixing or mess up with taking of some mix, replace with water, mesure amps,  and repeat until you’ve reached the desired value.

To help you:

– 3 to 4 flat teaspoons and/or 4 amps for a basic HHO cell (used alone or in parallel) ie,WalkingEagleSolution or GreenTechexpress, represents a not to cross boundary.

– 1 teaspoon of baking soda in a Mason Jar HHO cell type (used alone or in parallel)  generates a consumption of about 1 amps and gas production of 0.1 liter/minute

Add the bicarbonate or a ½ teaspoon after each refueling, always use the same spoon to always add the same amount, or if you get one a digital scale. You can find very affordable scales on amazon

I hope this article will help you optimize your settings. All this may seem a bit complicated, but it’s worth it. Feel free to leave a comment and tell us how all this is running for you !

Whish you nice savings.

Christian, Your Brother in HHO.

Technorati Tags: , , , , , , , , ,

Sep
18

Beware not to become HHO-aholic !

Posted under Do It Yourself HHO Cell, HHO Cell Users Testimonials by admin

This Guy is a Great ressource ! Can’t be more sincere.



Here is a list of stores where you can find do it yourself kits & parts :


DIY HHO Cell Kits on GreentechExpress


DIY HHO Cell Kits on HHO-Canada


DIY HHO Cell Kits on HHOKitsDirect


Ressources for Do It Yourself Plans :


PunhHHO Ebook + Videos DryCellPLans

A paid offer but you also can grab a free Dry Cell Plans PDF Ebook


HHOKitsDirect Ebook + Videos HHO Cell Plans

Do it Yourself Paid offer but  you can grab a 7 day free course.


Go Ahead Boys & Girls !


Technorati Tags: , , , , , , , ,